Prepared by: Assist. Lect. Kawther Hayder Abdulateef
College of Engineering, Department of Civil Engineering
Reliance on assessing and rehabilitating existing structures, rather than demolishing and rebuilding them, is growing worldwide for economic, environmental, and technical reasons. This paper reviews the general framework for assessing existing structures, the main deterioration mechanisms, inspection and monitoring techniques, probabilistic assessment approaches, and strengthening and life-extension methods, with a focus on concrete structures. Keywords: assessment of existing structures, service life, durability, reinforcement corrosion, structural health monitoring, strengthening.
Structures are usually designed for a service life of fifty to one hundred years, yet many are approaching the end of this life or have already exceeded it, while service loads, design requirements, and environmental conditions change. This has made the assessment of existing structures a distinct branch of structural engineering. It differs from new design in that the engineer deals with a structure that already exists, with a loading history and an actual material condition that can be measured, and does not rely on conservative assumptions alone. The international standard ISO 13822 affirms this distinction by setting out a staged procedure based on the principles of structural reliability and the consequences of failure. It begins with defining the assessment objective, reviewing documents, and carrying out a preliminary inspection, then moves to detailed inspection, analysis, and safety verification, and ends with a recommendation for appropriate action (ISO, 2010). Codes such as ACI 562 and ACI 437R follow a similar logic: they define steps for evaluating the actual strength of concrete members and allow load testing to be used when calculations alone are insufficient (ACI Committee 562, 2019; ACI Committee 437, 2019).
The assessment process begins with understanding the deterioration mechanisms, because the type of deterioration determines the inspection approach and the treatment method. Corrosion of reinforcing steel caused by chloride ions or carbonation is among the most serious causes of deterioration in concrete structures. Tuutti described it with a two-stage model: an initiation stage, in which the corrosion-causing agent reaches the steel surface, followed by a propagation stage, in which corrosion advances and causes cracking, spalling, and loss of steel cross-section (Tuutti, 1982; Bertolini et al., 2013). Sulfate reactions, alkali–aggregate reaction, freeze–thaw cycles, and hydraulic erosion in water structures add to this, and these factors are aggravated in hot and saline environments (Mehta & Monteiro, 2014). Consequently, a reliable assessment does not rely only on reviewing the original design drawings, but requires measuring the actual condition of the materials and members.
Inspection methodology combines non-destructive and partially destructive methods. The rebound hammer and ultrasonic pulse velocity are used to estimate the uniformity and strength of the concrete; half-cell potential and electrical resistivity measurements are used to assess the likelihood of corrosion; the locations of reinforcing steel are detected by ground-penetrating radar or magnetic surveys; and core samples are taken to confirm strength and to measure carbonation depth and chloride concentration (Bertolini et al., 2013). It is preferable to correlate non-destructive test results with core samples to calibrate them, because estimating strength by indirect methods alone carries considerable uncertainty.
After data collection comes the analysis stage, in which one can adopt deterministic models based on partial safety factors adjusted with site information, or probabilistic models that account for variability in loads, resistance, and deterioration over time. The probabilistic approach makes it possible to predict the evolution of the reliability index over the remaining life, and to compare maintenance and intervention alternatives on the basis of life-cycle cost (Frangopol et al., 2004). Life-cycle cost studies show that selecting protection strategies for concrete structures exposed to chlorides is justified on the basis of total cost, not initial cost alone (Val & Stewart, 2003). For seismic assessment, ASCE/SEI 41 provides a performance-based framework that defines target performance levels and evaluates members on the basis of their deformation capacity, not strength alone (ASCE, 2023).
Advances in structural health monitoring contribute to improving assessment accuracy. Sensors installed on the structure make it possible to measure stresses, strains, and vibrations and their changes over time, and to detect changes in dynamic properties that may indicate damage. This methodology rests on comparing the structure's current behavior with its baseline behavior, thereby shifting maintenance from a fixed periodic approach to one based on actual condition (Farrar & Worden, 2007).
When intervention is found to be necessary, there are several options for extending service life. Repair treatment includes removing damaged concrete, cleaning and repairing the reinforcing steel, and replacing damaged sections with suitable repair mortars, together with additional protective measures such as cathodic protection, corrosion inhibitors, and barrier coatings (Bertolini et al., 2013). Strengthening includes enlarging member sections by concrete or steel jacketing, and strengthening members by externally bonding fiber-reinforced polymer (FRP) plates or fabrics. This technique is characterized by light weight, non-corrosiveness, and ease of installation, and design guidance for it is given in ACI PRC-440.2 (ACI Committee 440, 2023). Seismic behavior can also be improved by adding shear walls, braces, or base isolators, or by reducing the applied loads by changing the use of the structure. The choice of solution should be based on a technical, economic, and environmental comparison, because extending the life of an existing structure usually reduces the carbon emissions associated with producing and transporting new materials, but this does not hold if the cost of repeated intervention exceeds the cost of replacement.
In conclusion, extending the life of existing structures is an integrated process that begins with defining objectives and understanding deterioration mechanisms, passes through field and laboratory inspection and deterministic or probabilistic analysis, and ends with selecting a suitable intervention and monitoring its subsequent performance. There remains a need for research that takes local conditions into account, such as high temperatures and soil and water salinity, and that develops deterioration models specific to local materials and to hydraulic structures.
References
ACI Committee 437. (2019). ACI 437R-19: Strength Evaluation of Existing Concrete Buildings. American Concrete Institute.
ACI Committee 440. (2023). ACI PRC-440.2-23: Design and Construction of Externally Bonded Fiber-Reinforced Polymer (FRP) Systems for Strengthening Concrete Structures—Guide. American Concrete Institute.
ACI Committee 562. (2019). ACI 562-19: Code Requirements for Assessment, Repair, and Rehabilitation of Existing Concrete Structures and Commentary. American Concrete Institute.
ASCE. (2023). ASCE/SEI 41-23: Seismic Evaluation and Retrofit of Existing Buildings. American Society of Civil Engineers.
Bertolini, L., Elsener, B., Pedeferri, P., Redaelli, E., & Polder, R. (2013). Corrosion of Steel in Concrete: Prevention, Diagnosis, Repair (2nd ed.). Wiley-VCH.
Farrar, C. R., & Worden, K. (2007). An introduction to structural health monitoring. Philosophical Transactions of the Royal Society A, 365(1851), 303–315.
Frangopol, D. M., Kallen, M. J., & van Noortwijk, J. M. (2004). Probabilistic models for life-cycle performance of deteriorating structures: review and future directions. Progress in Structural Engineering and Materials, 6(4), 197–212.
ISO. (2010). ISO 13822:2010: Bases for design of structures — Assessment of existing structures. International Organization for Standardization.
Mehta, P. K., & Monteiro, P. J. M. (2014). Concrete: Microstructure, Properties, and Materials (4th ed.). McGraw-Hill.
Tuutti, K. (1982). Corrosion of Steel in Concrete. Swedish Cement and Concrete Research Institute, Stockholm.
Val, D. V., & Stewart, M. G. (2003). Life-cycle cost analysis of reinforced concrete structures in marine environments. Structural Safety, 25(4), 343–362.