Seismic Performance and Rehabilitation of Deteriorated Reinforced Concrete Drainage Supports under Reversed Cyclic Loading

  Share :          
  25

Prepared by: Asst. Lecturer Kawther Hayder Abdulateef, College of Engineering – Department of Civil Engineering Abstract Reinforced concrete supports for water drainage structures, including columns, piers, retaining walls, channel shoulders, and crossing structures, are critical elements in keeping drainage, irrigation, and flood-protection systems operating. Throughout their service life, these supports are exposed to harsh environmental conditions, including permanent moisture, salts, sulfates, chlorides, and wetting-drying cycles, so they deteriorate gradually before any seismic event occurs. When exposed to ground motion, they are subjected to reversed cyclic loads that reveal weaknesses in their ductility and energy dissipation capacity. This article reviews the mechanisms of deterioration and their effect on seismic behavior, the indicators used to assess performance, the main rehabilitation and strengthening techniques, and the criteria for selecting the optimal solution. Keywords: Seismic performance, reversed cyclic loading, reinforcement corrosion, water drainage supports, rehabilitation, fiber-reinforced polymer wrapping, ductility. 1. Introduction The safety of drainage networks and water channels depends on the efficiency of their supporting structural elements. If one of these elements fails to perform its function during or after an earthquake, service is interrupted and flood and environmental risks are aggravated, in addition to the high cost of repair. These structures operate in a humid environment adjacent to soil and water, which accelerates deterioration compared with dry structures [1]. Reversed cyclic loading refers to loads in which lateral push and pull forces alternate on an element, and it is the laboratory representation closest to the effect of earthquakes on reinforced concrete elements. It is used to evaluate indicators such as lateral capacity, stiffness degradation, energy dissipation, and ductility. 2. Mechanisms of Deterioration in Water Drainage Supports 2.1 Reinforcement corrosion. Corrosion caused by chlorides and carbonation is the most prominent cause of deterioration. It leads to a reduction in the effective cross-sectional area of the bars, a decrease in their ductility, and cracking and spalling of the concrete cover due to the pressure of corrosion products [1][2][3]. Corrosion also weakens the bond between steel and concrete, reducing the efficiency of lap splices and the transfer of stresses [1][2]. 2.2 Concrete deterioration. In these environments, concrete is exposed to sulfate attack, wetting-drying cycles, and surface erosion caused by the flow of sediment-laden water, which increases porosity and reduces strength and stiffness. 2.3 Deterioration of structural details. Older structures often date back to specifications that predate modern seismic requirements, and so they feature wide stirrup spacing, limited transverse confinement, and short lap lengths. These deficiencies increase the likelihood of shear failure, buckling of longitudinal bars, and slippage of lap splices under cyclic loading [7]. 3. Seismic Behavior under Reversed Cyclic Loading Laboratory studies on corroded columns show that deterioration changes both the failure mode and the hysteretic response [4][5]. The main observations can be summarized as follows: Reduced lateral capacity and ductility: Loss of steel area and cracking of the cover reduce the ultimate capacity and the ability to deform before failure. Accelerated stiffness degradation: Cracks widen with repeated cycles, and the effective stiffness declines faster than in sound elements. Weakened energy dissipation: Hysteresis loops narrow and show pinching due to slippage and weakened bond, which reduces the energy dissipated per cycle. Shift in failure mode: Failure may shift from a ductile flexural mode to a brittle shear or buckling mode, which is the greatest threat to the safety of the structure. The situation is further complicated in drainage supports by hydraulic effects, as the surrounding water adds an effective hydrodynamic mass that alters the dynamic properties of the element [6], and soil-structure interaction also affects the distribution of forces and deformations [7]. 4. Condition and Performance Assessment The assessment of a deteriorated support begins with field and laboratory inspection that includes visual survey of cracks and spalling, non-destructive and destructive concrete testing, measurement of carbonation depth and chloride content, and estimation of steel section loss and corrosion potential [1][8]. The residual capacity is then determined through structural analysis, and the seismic demand is compared with the capacity, with nonlinear static analysis used when necessary. International standards provide a systematic framework for this assessment [8][9]. 5. Rehabilitation and Strengthening Techniques The treatment depends on the level of deterioration, the strengthening objective (flexure, shear, or ductility), and the operating environment. The main solutions are: 5.1 Local repair and section restoration. This involves removing damaged concrete, cleaning the steel and protecting it with anti-corrosion coatings, replacing or supplementing damaged bars, and then restoring the section with suitable repair mortar or concrete [8]. 5.2 Fiber-reinforced polymer (FRP) wrapping. The support is wrapped with carbon or glass fiber sheets to increase lateral confinement, which raises shear strength and ductility and improves the behavior of lap splices. Research has demonstrated its effectiveness in both deteriorated and undeteriorated columns [10][11]. Its advantages include light weight, speed of installation, no significant increase in element dimensions, and good resistance to chemical corrosion; however, it must be protected from continuous moisture and ultraviolet radiation in accordance with manufacturer recommendations and standards [12]. 5.3 Steel jackets. Steel jackets with mortar infill are used to increase shear strength and ductility. They are suitable for circular columns with a high need for confinement, and the steel must be protected from corrosion in the aquatic environment [7]. 5.4 Reinforced concrete jacketing. A reinforced concrete layer is added around the existing element to increase the cross-section and the flexural and shear capacities. Its efficiency depends on the quality of bond with the old concrete and the anchorage details, and its drawbacks include increased dimensions and weight and the resulting effect on the hydraulic cross-section [7][9]. 5.5 Complementary treatments. These include cathodic protection, the addition of corrosion inhibitors, improved drainage around the base, and strengthening of foundations where necessary, to ensure that the foundation or surrounding soil does not become the weakest link after the upper element is strengthened [1]. 6. Criteria for Selecting the Optimal Solution No single solution suits all cases, and the following should be considered: Identify the governing failure mode (shear, flexure, or lap splice) and target its treatment directly. Consider the effect of strengthening on the hydraulic cross-section, flow efficiency, and subsequent maintenance cost. Ensure the material suits the environment (permanent moisture, salts, thermal variation) and that the site is accessible for execution. Evaluate cost over the structure’s life cycle, not only the initial execution cost. Verify the design through nonlinear analysis or laboratory models when the structure is of high importance. 7. Conclusion Scientific evidence shows that the deterioration of reinforced concrete supports for water drainage structures, particularly due to reinforcement corrosion, reduces their ductility and energy dissipation capacity and shifts their failure mode toward more brittle modes under reversed cyclic loading. This calls for careful field and laboratory assessment before selecting a treatment method, followed by adopting a solution that addresses the governing failure mode and suits the aquatic environment. Periodic maintenance and early monitoring remain less costly and more effective than treatment after damage has occurred. Further experimental studies on drainage supports specifically are recommended, since most of the available data is derived from bridge and building columns. References Bertolini, L., Elsener, B., Pedeferri, P., Redaelli, E., & Polder, R. (2013). Corrosion of Steel in Concrete: Prevention, Diagnosis, Repair (2nd ed.). Wiley-VCH. Rodriguez, J., Ortega, L.M., & Casal, J. (1997). Load carrying capacity of concrete structures with corroded reinforcement. Construction and Building Materials, 11(4), 239–248. Apostolopoulos, C.A., & Papadakis, V.G. (2008). Consequences of steel corrosion on the ductility properties of reinforcement bar. Construction and Building Materials, 22(12), 2316–2324. Ma, Y., Che, Y., & Gong, J. (2012). Behavior of corrosion damaged circular reinforced concrete columns under cyclic loading. Construction and Building Materials, 29, 548–556. Meda, A., Mostosi, S., Rinaldi, Z., & Riva, P. (2014). Experimental evaluation of the corrosion influence on the cyclic behaviour of RC columns. Engineering Structures, 76, 112–123. Liaw, C.Y., & Chopra, A.K. (1974). Dynamics of towers surrounded by water. Earthquake Engineering & Structural Dynamics, 3(1), 33–49. Priestley, M.J.N., Seible, F., & Calvi, G.M. (1996). Seismic Design and Retrofit of Bridges. Wiley. ACI Committee 562. (2019). ACI 562-19: Assessment, Repair, and Rehabilitation of Existing Concrete Structures. American Concrete Institute. ASCE/SEI 41-17. (2017). Seismic Evaluation and Retrofit of Existing Buildings. American Society of Civil Engineers. Seible, F., Priestley, M.J.N., Hegemier, G.A., & Innamorato, D. (1997). Seismic retrofit of RC columns with continuous carbon fiber jackets. Journal of Composites for Construction, 1(2), 52–62. Bousias, S., Triantafillou, T., Fardis, M., Spathis, L., & O’Regan, B. (2004). Fiber-reinforced polymer retrofitting of rectangular reinforced concrete columns with or without corrosion. ACI Structural Journal, 101(4), 512–520. ACI Committee 440. (2017). ACI 440.2R-17: Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures. American Concrete Institute.